QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 1 of 8 www.qorvo.com 8 pin 2x2 mm dfn p ackage general description the QPL9095 is a high - linearity, ultra - low noise gain block amplifier with a bypass mode functionality integrated in the product. at 900m hz, the amplifier typically provides 22 db gain, +3 3 dbm oip3, and 0. 6 db noise figure while drawing 5 0 ma current from a + 4.2 ? v supply. the QPL9095 is internally matched using a high performance e - phemt process and only requires four external components for operation from a single positive supply: an external rf choke and blocking/bypass capacitors. this low noise amplifier contains an internal acti ve bias to maintain high performance over temperature. the QPL9095 is optimized for the 5 00mhz ? C ? 1000m hz frequency band and is targeted for wireless infrastruc ture. the QPL9095 is packaged in a 2?x?2?mm dfn. applications ? base - station receivers ? repeaters / das ? tower mounted amplifiers ? mobile infrastructure ? general purpose wireless ? tdd or fdd systems product features ? 5 00mhz C 1000m hz operational bandwidth ? lna with integrated bypass mode ? ability to turn lna and bypass mode off ? ultra low noise, 0. 6 db at 900m hz ? 22 db gain at 900m hz ? +3 3 dbm output ip3 in lna mode ? +3 5 dbm out put ip3 in bypass mode ? internally matched ? positive supply only, +3.3 to +5?v ? 2x2 mm 8 - pin dfn plastic package functional block diagram top view ordering information part no. description QPL9095 sr 100 pcs on 7 reel QPL9095 tr7 2500 pcs on 7 reel QPL9095evb01 evaluation board ? b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k 8 7 6 5 1 2 3 4 v d d r f o u t g n d v s d g n d r f i n n / c v b y p
QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 2 of 8 www.qorvo.com absolute maximum ratings parameter rating storage temperature ?6 5 to 150c supply voltage (v dd ) + 7 v rf input power, cw, 50, t=25 c +30 dbm operation of this device outside the parameter ranges given above may cause permanent damage. recommended operating conditions parameter min typ max units supply voltage (v dd ) 3. 0 4.2 5.25 v t case ? 40 + 105 c t j at t case = 125 c + 1 4 2 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. electrical specifications test conditions unless otherwise noted: v dd = +4.2 v, temp.=+ 25 c . parameter conditions min typ max units operational frequency range 500 10 00 mhz test frequency 900 mhz gain lna on, bypass off 20.5 22 23.5 db input return loss lna on, bypass off 8.5 db output return loss lna on, bypass off 11 db noise figure (2) lna on, bypass off 0.6 0.9 db output p1db (1) lna on, bypass off +18.5 +20 dbm output ip3 lna on, bypass off, pout=+2 dbm/tone, f=1 mhz +30 +33 dbm insertion loss lna off, bypass on 1.2 2.5 db return loss lna off, bypass on 12 db isolation (1) lna off, bypass off 15 18 db output ip3 lna off, bypass on pin=+2 dbm/tone, f=1 mhz +30 +35 dbm control voltage, v 1 , v 2 v ih 1.17 v dd v v il 0 0. 63 v current, i d bypass off 40 53 75 ma bypass on 5 ma switching speed lna - bypass (50% vctrl to 10% rf) 40 ns bypass - lna(50% vctrl to 90% rf) 185 ns lna - off(50% vctrl to 10% rf) 40 ns off - lna(50% vctrl to 90% rf) 65 ns thermal resistance, jc channel to case 44 c/w 1. minimum s pecification listed is guaranteed by design. not tested in production. 2. input trace loss de - embedded from noise figure data. control truth table v byp v sd state 0 0 lna on, bypass off 0 1 lna off, bypass off 1 x lna off, bypass on ?
QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 3 of 8 www.qorvo.com QPL9095 evaluation board notes: 1. a through line is included on the evaluation board to de - embed the board losses. bill of material C QPL9095 evaluation board reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ultra low noise, bypass lna qorvo QPL9095 c10 1000 pf cap, 0402, 10%, 50v, x7r murata grm155r71h102ka01d (1067924) c 9 1.0 uf cap., 0402, 10%, 6.3 v, x5r murata grm155r60j105ke19d (1068381) c1, c4, c 5, c8 100 pf cap., 0402, 5%, 50v, npo/cog murata grm1555c1h101jz01d (1068365) r1, 3, 4 0 resistor, chip, 0402, 5%, 1/16w various c11, c12 20k resistor, chip, 0402, 5%, 1/16w various l1 6 8 nh inductor, 0 603 , 5%, coil coilcraft ? l 1 c 1 0 c 9 r 3 u 1 c 8 c 5 c 4 r 4 r 1 c 1 c 1 1 c 1 2 j 2 r f o u t p u t j 6 g n d j 3 v d d j 1 r f i n p u t l 1 6 8 n h ( 0 6 0 3 ) c 4 1 0 0 p f c 1 1 0 0 p f c 1 0 1 0 0 0 p f c 9 1 u f r 3 0 ? 8 7 6 5 1 2 3 4 j 5 v 1 j 4 v 2 r 4 0 ? r 1 0 ? u 1 c 1 2 2 0 k c 1 1 2 0 k
QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 4 of 8 www.qorvo.com performance plots test conditions unless otherwise noted: v dd = + 4.2 v, temp.=?+25?c ? 10 13 16 19 22 25 0 500 1000 1500 2000 2500 3000 3500 4000 gain (db) frequency (mhz) gain vs. frequency (lna mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 0 500 1000 1500 2000 2500 3000 3500 4000 |s11| (db) frequency (mhz) input return loss vs. frequency (lna mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 0 500 1000 1500 2000 2500 3000 3500 4000 |s22| (db) frequency (mhz) output return loss vs. frequency (lna mode) +95? c +25? c ?40? c -5 -4 -3 -2 -1 0 500 1000 1500 2000 2500 3000 3500 4000 gain (db) frequency (mhz) gain vs. frequency (bypass mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 500 1000 1500 2000 2500 3000 3500 4000 |s11| (db) frequency (mhz) input return loss vs. frequency (bypass mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 500 1000 1500 2000 2500 3000 3500 4000 |s22| (db) frequency (mhz) output return loss vs. frequency (bypass mode) +95? c +25? c ?40? c -30 -25 -20 -15 -10 500 1000 1500 2000 2500 3000 3500 4000 isolation (db) frequency (mhz) isolation vs. frequency (off mode) +95? c +25? c ?40? c -5 -4 -3 -2 -1 0 0 500 1000 1500 2000 2500 3000 3500 4000 |s11| (db) frequency (mhz) input return loss vs. frequency (off mode) +95? c +25? c ?40? c -10 -8 -6 -4 -2 0 0 500 1000 1500 2000 2500 3000 3500 4000 |s22| (db) frequency (mhz) output return loss vs. frequency (off mode) +95? c +25? c ?40? c 28 29 30 31 32 33 34 35 36 37 -3 -2 -1 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (lna mode) +95? c +25? c ?40? c 900 mhz f = 1 mhz 25 30 35 40 45 -3 -2 -1 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (bypass mode) +95? c +25? c ?40? c 900 mhz f = 1 mhz 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.5 1 1.5 2 2.5 noise figure (db) frequency (ghz) noise figure vs frequency +95? c +25? c ?40? c
QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 5 of 8 www.qorvo.com QPL9095 improved return loss tune performance plots test conditions unless otherwise noted: v dd = +4.2 v, temp.=?+25?c ? l 1 c 1 0 c 9 r 3 u 1 c 8 c 5 0 ? r 4 r 1 c 1 c 1 1 c 1 2 l 2 c 1 3 c 2 l 3 j 2 r f o u t p u t j 8 g n d j 3 v d d j 1 r f i n p u t l 1 6 8 n h c 2 1 0 0 p f c 1 1 0 0 p f c 1 0 1 0 0 0 p f c 9 1 u f r 3 0 ? 8 7 6 5 1 2 3 4 j 5 v 1 j 4 v 2 r 4 0 ? r 1 0 ? u 1 c 1 2 2 0 k c 1 1 2 0 k l 2 5 . 6 n h c 1 3 2 2 p f l 3 2 5 n h 20 21 22 23 24 25 700 800 900 1000 gain (db) frequency (mhz) gain vs. frequency lna mode -25 -20 -15 -10 -5 0 700 800 900 1000 |s11| & |s22| (db) frequency (mhz) return loss vs. frequency input return loss output return loss lna mode -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 700 800 900 1000 insertion loss (db) frequency (mhz) insertion loss vs. frequency bypass mode -25 -20 -15 -10 -5 0 700 800 900 1000 |s11| & |s22| (db) frequency (mhz) return loss vs. frequency input return loss output return loss bypass mode 28 29 30 31 32 33 34 35 -3 -2 -1 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone 700 mhz 800 mhz 900 mhz 1000 mhz lna mode 35 36 37 38 39 40 41 42 43 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone 700 mhz 800 mhz 900 mhz 1000 mhz bypass mode 0.0 0.2 0.4 0.6 0.8 1.0 700 800 900 1000 noise figure (db) frequency (mhz) noise figure vs frequency
QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 6 of 8 www.qorvo.com evaluation board pcb information qorvo pcb 28 1865 material and stack - up 50 ohm line dimensions: width = 0.0 182 , spacing = 0.0 20 pin configuration and description pin no. label description 1, 6 gnd rf/dc ground pin. 2 rfin rf input pin. dc block required. 3 n /c no internal connection. provide grounded pcb land pads for mounting integrity. 4 v byp control pin for bypass mode . the lna is automatically turned off when the bypass mode is activated. refer to truth table on pg 2. 5 v sd control pin to disable the lna. refer to truth table on pg. 2. 7 rfout rf output pin. dc block required. 8 v dd supply voltage pin. external choke and bypass capacitors needed. backside paddle rf/dc gnd rf/dc ground. follow recommended via pattern and ensure good solder attach for best thermal and electrical performance. ? b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k 8 7 6 5 1 2 3 4 v d d r f o u t g n d v s d g n d r f i n n / c v b y p r o g e r s 4 0 0 3 c r = 3 . 5 t y p . 1 o z . c u b o t t o m l a y e r f r 4 f r 4 1 o z . c u t o p l a y e r 1 o z . c u i n n e r l a y e r 1 o z . c u i n n e r l a y e r 0 . 0 6 2 " 0 . 0 0 6 " f i n i s h e d b o a r d t h i c k n e s s 0 . 0 0 8 " 0 . 0 0 8 "
QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 7 of 8 www.qorvo.com mechanical information package marking and dimensions n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this part outline conforms to jedec standard mo - 220, issue e (variation vggc) for thermally enhanced plastic very thin fine pitch quad flat no lead package (qfn). 3. dimension and tolerance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp - 012. pcb mounting pattern n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 4. ensure good package backside paddle solder attach for reliable operation and best electrical performance. 9 095 trace code ?
QPL9095 ultra low - noise, bypass lna d ata sheet ju ly 6 , 201 7 | subject to change without notice 8 of 8 www.qorvo.com rohs compliance this part is compliant with 2011/65/eu rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment) as amended by directive 2015/863/eu. this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free handling precautions parameter rating standard caution! esd - sensitive device esd? C ?human body model (hbm) class 1b esda?/?jedec js - 00 1 - 20 14 esd? C ?charged device model ( cd m) class c3 esda / jedec js - 002 - 2014 msl? C ?moisture sensitivity level 1 ipc/jedec j - std - 020 solderability compatible with lead - free (260c max. reflow temp.) soldering process. solder profiles available upon request. contact plating: nipdau contact information for the latest specifications, additional product information, worldwide sales and distribution locations : web: www.qorvo.com tel: 1 - 844 - 890 - 8163 email: customer.support@qorvo.com for technical questions and application information: email: appsupport@qorvo.com important notice the information contained herein is believed to be reliable; however, qorvo makes no warranties regarding the information con tained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. all informatio n contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for qorvo products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anythin g described by such information. this information does not constitute a warranty with respect to t he products described herein, and qorvo hereby disclaims any and all warranties with respect to such products whether express or implied by law, course of dealing, course of performance, usage of trade or otherwise, including the implied warranties of merc hantability and fitness for a particular purpose. without limiting the generality of the foregoing, qorvo products are not warranted or authorized for use as critical componen ts in medical, life - saving, or life - sustaining applications, or other application s where a failure would reasonably be expected to cause severe personal injury or death. copyright 2016 ? qorvo, inc. | qorvo is a registered trademark of qorvo, inc. contact information for the latest specifications, additional product information, worldwide sales and distribution locations : web: www.qorvo.com tel: 1 - 844 - 890 - 8163 email: customer.support@qorvo.com for technical questions and application inf ormation: email: appsupport@qorvo.com p b ?
|
